Embedding Sensors and Motors will introduce you to the design of sensors and motors, and to methods that integrate them into embedded systems used in consumer and industrial products. You will gain hands-on experience with the technologies by building systems that take sensor or motor inputs, and then filter and evaluate the resulting data. You will learn about hardware components and firmware algorithms needed to configure and run sensors and motors in embedded solutions.
Специализация Embedding Sensors and Motors
Experience Sensors and Motors in an IoT World. Master sensor and motor theory, and program these devices in a microprocessor system.
1,748 уже зарегистрированы!
от партнера
1,748 уже зарегистрированы!
Специализация: общие сведения
Недавно просмотрено: 10,061
Чему вы научитесь
Study a lab experiment or production process and understand how to specify the proper sensor solution for taking real-time process data
Implement the sensor into an embedded system in both hardware and software
Modify existing hardware schematic to add sensors and all support circuitry needed to implement the signal chain in existing microprocessor system
Create hardware and firmware to process the sensor signal and feed data to a microprocessor for further evaluation
Приобретаемые навыки
sensor integrationfirmwaremotor designembedded engineeringhardware
О специализации
Пройти курсы
Специализация Coursera — это серия курсов, помогающих в совершенстве овладеть определенным навыком. Можно сразу записаться на специализацию или просмотреть курсы, из которых она состоит и выбрать тот, с которого вы хотите начать. Подписываясь на курс, который входит в специализацию, вы автоматически подписываетесь на всю специализацию. Можно завершить всего один курс, а потом сделать паузу в обучении или в любой момент отменить подписку. Отслеживайте свои курсы и прогресс на панели управления учащегося.
Практический проект
В каждой специализации есть практический проект, который нужно успешно выполнить, чтобы завершить специализацию и получить сертификат. Если для практического проекта в специализации предусмотрен отдельный курс, прежде чем начать его, необходимо завершить все остальные курсы.
Получите сертификат
Когда вы пройдете все курсы и завершите практический проект, вы получите сертификат, которым можно поделиться с потенциальными работодателями и коллегами.
Специализация включает несколько курсов: 4
Курс1
Sensors and Sensor Circuit Design
4.5
Оценки: 81
After taking this course, you will be able to: ● Understand how to specify the proper thermal, flow, or rotary sensor for taking real-time process data. ● Implement thermal sensors into an embedded system in both hardware and software. ● Add the sensor and sensor interface into a microprocessor based development kit. ● Create hardware and firmware to process sensor signals and feed data to a microprocessor for further evaluation. ● Study sensor signal noise and apply proper hardware techniques to reduce it to acceptable levels. You will need to buy the following components to do the two course projects based on the videos in this module. Note that if you have already purchased the PSOC 5LP PROTOTYPING KIT, you do not need to buy it again. These parts may be purchased off the Digikey web site, www. Digikey.com. Or, you may obtain the specs from the site, and purchase them elsewhere. These are the part numbers typed out, so you can copy and paste them into the Digikey web site. You will need one of each part. 428-3390-ND NHD-0216BZ-RN-YBW-ND 570-1229-ND A105970CT-ND
Курс2
Motors and Motor Control Circuits
4.5
Оценки: 59
This is our second course in our specialization on Embedding Sensor and Motors. To get the most out of this course, you should first take our first course entitled Sensors and Sensor Circuits. Our first course gives you a tutorial on how to use the hardware and software development kit we have chosen for the lab exercises. This second course assumes that you already know how to use the kit. After taking this course, you will be able to: ● Understand how to specify the proper AC or DC motor for a machine design. ● Integrate the motor to a machine, based on analysis of motor equations for voltage, current, torque and speed. ● Implement the motor and accompanying rotary sensor into a motor control circuit in both hardware and software. ● Add a motor and motor control circuit into a microprocessor based development kit. ● Create hardware and firmware to process motor feedback data to a microprocessor for further evaluation. You will need to buy the following components to do the two course projects based on the videos in this module. Note that if you have already purchased the PSOC 5LP PROTOTYPING KIT, you do not need to buy it again. These parts may be purchased off the Digikey web site, www. Digikey.com. Or, you may obtain the specs from the site, and purchase them elsewhere. These are the part numbers for the above table, the lab on Motor Voltage and Current Measurement. You can copy and paste them into the search engine on the Digikey web site. You need one of each except for the AA batteries (N107-ND), which you would need 3. 428-3390-ND P14355-ND FQU13N10LTU-ND N107-ND 1N5393-E3/54GICT-ND RNF14FTD1K00CT-ND P0.62W-1BK-ND These are the part numbers for the above table, so you can copy and paste them into the search engine on the Digikey web site. You will need one of each. 428-3390-ND 987-1188-ND
Курс3
Pressure, Force, Motion, and Humidity Sensors
4.4
Оценки: 10
After taking this course, you will be able to: ● Understand how to specify the proper pressure, force, strain, position, motion, acceleration, occupancy, and humidity sensors for taking real-time process data. ● Implement these sensors into an embedded system in both hardware and software. ● Add the sensor and sensor interface into a microprocessor based development kit. ● Create hardware and firmware to process sensor signals and feed data to a microprocessor for further evaluation. In this course you will build the circuit from Video 7 (Lab Exercise on strain gauges), Module 2 (Force and Strain Sensors and Touch Screens), and use it to make screen shots of the timing of the switch. If you haven't already wired up the system and written all the software per the instructions of Video 7, please do so now. You will need to buy the following components to complete this assignment. Note that if you have already purchased the PSOC 5LP PROTOTYPING KIT, you do not need to buy it again. These parts may be purchased off the Digikey web site, www. Digikey.com. One part needs to be purchased off the Sparkfun website www.sparkfun.com. Or, you may obtain the specs from the site, and purchase them elsewhere. Digikey Part numbers are typed out here: 428-3390-ND CF14JT22K0CT-ND CF14JT100KCT-ND Table shown here: Index Quantity Part Number Description 1 1 428-3390-ND PSOC 5LP PROTOTYPING KIT 2 2 CF14JT22K0CT-ND RES 22K OHM 1/4W 5% AXIAL 3 1 CF14JT100KCT-ND RES 100K OHM 1/4W 5% AXIAL Sparkfun part numbers are typed out here: TAL221 Table shown here: Index Quantity Part Number Description 1 1 TAL221 Mini-load cell - 100g, straight bar
Курс4
Sensor Manufacturing and Process Control
This is our fourth course in our specialization on Embedding Sensor and Motors. To get the most out of this course, you should first take our first course entitled "Sensors and Sensor Circuits", our second course entitled "Motor and Motor Control Circuits", and our third course entitled "Pressure, Force, Motion, and Humidity Sensors". Our first course gives you a tutorial on how to use the hardware and software development kit we have chosen for the lab exercises. Our second and third courses give you three hands-on lab experiments using the kit. This third course assumes that you already know how to use the kit. You will learn about sensor signal characterization and manufacturing techniques and how to optimize the accuracy of sensors. You will also learn about more advanced sensors, proportional-integral-derivative (PID) control, and how this method is used to give you a closed loop sensor feedback system. After taking this course, you will be able to: ● Understand how sensor manufacturers characterize and calibrate their sensors. ● Tune a PID control loop and access the PID control function of the Cypress PSoC development kit for a motor control application. ● Understand manufacturing methods used to build electro-mechanical and micro-machined sensors. You will need to buy the following components to do the two course projects based on the videos in this module. Note that if you have already purchased the PSOC 5LP PROTOTYPING KIT, you do not need to buy it again. These parts may be purchased off the Digikey web site, www. Digikey.com. Or, you may obtain the specs from the site, and purchase them elsewhere. All are quantity one except for N107-ND where you need three, and 493-15371-ND where you need two. 428-3390-ND P14355-ND FQU13N10LTU-ND N107-ND 1N5393-E3/54GICT-ND RNF14FTD1K00CT-ND P0.62W-1BK-ND 493-15371-ND
Преподаватели
James Zweighaft
InstructorElectrical, Computer & Energy Engineering
Jay Mendelson
InstructorElectrical, Computer & Energy Engineering
Сделайте шаг навстречу диплому магистра.
Специализация входит в онлайн-программу ''Master of Science in Electrical Engineering' от партнера Колорадский университет в Боулдере.
Если вы переходите на полную программу, курсы засчитываются при получении диплома.
О Колорадский университет в Боулдере
CU-Boulder is a dynamic community of scholars and learners on one of the most spectacular college campuses in the country. As one of 34 U.S. public institutions in the prestigious Association of American Universities (AAU), we have a proud tradition of academic excellence, with five Nobel laureates and more than 50 members of prestigious academic academies.
Часто задаваемые вопросы
Какие правила возврата средств?
Можно ли зарегистрироваться только на один курс?
Да! Чтобы начать, нажмите карточку интересующего вас курса и зарегистрируйтесь. Зарегистрировавшись, вы можете пройти курс и получить сертификат, ссылкой на который можно делиться с другими людьми. Просто ознакомиться с содержанием курса можно бесплатно. При подписке на курс, входящий в специализацию, вы автоматически подписываетесь на всю специализацию. Ход учебы можно отслеживать в панели управления учащегося.
Можно ли получить финансовую помощь?
Могу ли я пройти курс бесплатно?
Действительно ли это полностью дистанционный курс? Нужно ли мне посещать какие-либо занятия лично?
Это полностью дистанционный курс, потому вам не нужно ничего посещать. Все лекции, материалы для самостоятельного изучения и задания доступны всегда и везде по Интернету и с мобильных устройств.
Получу ли я зачеты в университете за прохождение специализации?
Остались вопросы? Посетите Центр поддержки учащихся.